![]() ![]() usr/local/Homebrew/Library/Homebrew/cask/cmd/abstract_command.rb:36:in `run' usr/local/Homebrew/Library/Homebrew/cask/cmd/install.rb:16:in `run' usr/local/Homebrew/Library/Homebrew/cask/cmd/install.rb:16:in `each' usr/local/Homebrew/Library/Homebrew/cask/cmd/install.rb:22:in `block in run' usr/local/Homebrew/Library/Homebrew/cask/installer.rb:101:in `install' usr/local/Homebrew/Library/Homebrew/cask/installer.rb:209:in `install_artifacts' usr/local/Homebrew/Library/Homebrew/cask/installer.rb:218:in `block in install_artifacts' usr/local/Homebrew/Library/Homebrew/cask/artifact/pkg.rb:52:in `run_installer' usr/local/Homebrew/Library/Homebrew/cask/artifact/pkg.rb:65:in `with_choices_file' usr/local/Homebrew/Library/Homebrew/cask/artifact/pkg.rb:59:in `block in run_installer' usr/local/Homebrew/Library/Homebrew/system_command.rb:33:in `run!' usr/local/Homebrew/Library/Homebrew/system_command.rb:29:in `run' usr/local/Homebrew/Library/Homebrew/system_command.rb:53:in `run!' usr/local/Homebrew/Library/Homebrew/system_command.rb:176:in `assert_success!' Contact the software manufacturer for assistance.) Installer: The install failed (The Installer encountered an error that caused the installation to fail. At this point, SoundFlower2ch and 64ch will appear as audio devices.It takes quite a while to install for no good reason. You may need to click ”Allow.”, then select “MATT INGALLS”. When you’re told that this has failed, go to “Security and Privacy” in System Preferences, and permit the software to load.Sudo installer -pkg Soundflower.pkg -target / ![]() It looks like something (perhaps a timeout?) is causing the graphical installer to fail prematurely. Hopefully this repeatable positive example should be enough to help the developers nail down the problem with their installer package. However, I have been able to get Soundflower installed by bypassing the graphical installer entirely and using the "install" terminal command. Say i want to play some audio in iTunes, but record it in Quicktime while listening to it out of the built-in speakers.That video has the feel of voodoo rather than solution. In the meantime, you can take your chances with an older version of Soundflowerbed, but you can do a lot with a Multi-Output Aggregate Device. NOTE: This is only the Soundflower kernel extension. Now you can follow the instructions above to get the "Allow" button to appear in the Security Preferences. Then click the "Open" button in that window to launch the installer. If so, click the "Open Anyway" button which will display another window. (**) If you see an "Open Anyway" button in the Security Preferences, this is something different!!! Most likely because you tried (and failed) opening the installer by double clicking without holding down the control key. If the "Allow" button is disabled, you may need to click the lock icon in the bottom lower left corner first. It should inform you installation was successful. Once there, there should be an "Allow" button (**) that you will need to click on to give permission to use Soundflower (developer: MATT INGALLS). The first time you run the installer (Soundflower.pkg), it will ask for your admin password, and will FAIL! A security alert will appear, with a button to take you to System Preferences "Security & Privacy - General" pane. ![]() Note that the even though this Soundflower extension is signed, but the installer is not! You will have to hold the control key down to open the Soundflower.pkg installer for the first time.Īpple makes you jump through a few hoops.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |